Yamaha surround sound hookup

Some guidelines
Contents:


  1. Option 1: HDMI® Connection Using the ARC Feature
  2. How to Hook up Surround Sound (with Pictures) - wikiHow
  3. How to Set up & Calibrate 5.1/6.1/7.1 Surround Sound Speaker System
  4. How to Connect a Stereo System

This means they will then compliment each other and one won't be way louder so effects will move around the room properly and sound natural. There are two ways to do this. If you have a low end system, the home theater in a box sort of setup, then the best way to calibrate is to use an spl meter. These don't cost a lot and make things far easier than trying to calibrate by ear. You need to play a test tone through your receiver one speaker at a time and set each speaker to the same level on the spl meter. This is done from your normal sitting position. As long as they're all the same level relative to each other, it doesn't actually matter too much what that level is, but a commonly used level is 75 db for each speaker in turn.

The subwoofer usually under reads on the spl meter due to their inaccuracy at measuring bass tones, so you may need to boost that up a little higher to have it matching the rest of the speakers. If you have the next level up from an all in one and have a receiver and speakers then you can get better results. Most receivers nowadays have an auto setup system which will calibrate for you. All of these systems attempt to do the same thing though which is set up your system for you, although the consensus tends to be that ARC is the best, followed by Audyssey, with the others behind that.

This is a matter of opinion and is the sort of thing AV geeks argue about, but that seems to be the way most people in the AV world think as far as I can tell. Anyway the way they work is that you set up a microphone which is supplied with the receiver at your listening position, the receiver will then play a test tone through each speaker in turn and then calibrate system levels and EQ the sound for you. There are still a couple of things you need to remember when doing this though. One thing to remember is that you need to make sure that the room is as quiet as possible.

Turn off any fans, close the windows etc as you don't want any banging, booming or rumbling from buses driving past to affect the final result. Set the subwoofer gain control to the middle of the dial. Set the crossover frequency on the subwoofer to maximum. The easiest way of holding the microphone at the correct height is with a tripod.


  1. dating someone with a large age gap.
  2. how do you know if your dating the right girl.
  3. signs you are dating someone with bipolar disorder.
  4. pondicherry dating sites;
  5. audio setup in yamaha rx-v receiver (hdmi arc) - HDMI - Streaming Video & TVs;
  6. How to Connect a Subwoofer to a Yamaha Receiver!
  7. So what is the .1 about?.

These don't cost a lot so buy one. Set it up at your main listening position, pointing straight up at the ceiling at ear height, then run the auto calibrate routine. If you don't have a tripod, you can put the microphone on your head and move around to different positions, but it's a bit of a pain to do it this way!

That's not to say I haven't done it like this myself in the past, but I'm glad I bought a tripod. A lot of these systems will give you a better result if you take multiple readings, you want to be roughly around the main seating position though as if you try to use different seats it will mess up the final calibration. Get as many readings as possible, usually the system asks you to move the mic 6 or 8 times. The more information it gets, the better the results.

There is a diagram below with suggested mic placement positions. The more advanced systems ask for more positions, if yours asks for 6 or 8 or so, just use the first 6 or 8 positions on this diagram for an idea of where to put the mic.

Remember that you're not calibrating for every possible position you're ever going to sit in on the sofa, but instead you're measuring the room for automatic room correction so make sure you do move the mic around. The first position is the main listening position so that's the most important, the sound will be optimised around that area. After the receiver has ran through its auto calibrate routine, then check what level the receiver has set the subwoofer also known as LFE level. The amount the receiver has had to boost or cut this level will then show up on the receiver.

If this has happened, simply adjust the gain on the back of the subwoofer up or down, depending on the reading, then calibrate it again by rerunning the receiver auto calibrate routine.

YAMAHA Receiver How to hook up home theater speakers wire

The ideal is to get it as close to 0 as possible, then there is no boosting or cutting between the receiver and the subwoofer, which leads to a minimum of distortion. If it's a few db above or below it's not the end of the world, so you don't need to get too obsessive, but just try and make sure it's not at the top of bottom of its range.

Different rooms affect sounds in different ways so sometimes you may need certain frequencies boosting or cutting, which you don't need to worry about as the receiver will try and do this for you. It does this by playing a full frequency range signal to each speaker, measuring how the room affects the sound then adjusting the output level and also the equalisation of the sound to try and produce what will end up at your ears as a neutral sound. After you've ran the auto calibrate setup program, then you will need to adjust the crossover and LFE cutoff level.

This is fairly straightforward. The THX standard is to set all of your speakers to small and then set the speakers crossover points to 80hz.

Option 1: HDMI® Connection Using the ARC Feature

The LFE channel for the subwoofer should then be set to hz. These are the recommended settings that Audyssey, THX etc recommend. The reason you set the crossover for the speakers at 80hz is that speakers struggle to reproduce the lowest frequencies you'll get from a soundtrack, which can go down to hz in some cases. If you set them to only play from 80hz upwards, then they don't distort and the sound is cleaner. The subwoofer will take the strain instead and do the job it's designed for, which is creating the low frequency effects. If you have small satellite speakers, they may not be able to reproduce sound down to 80hz, so you may have to have the crossover for them set a little higher.

The golden rule is you can always adjust your crossover up from what the receiver tells you it recommends, but never adjust it down, as if the system has had a go at playing a frequency through the speaker and it hasn't managed to reproduce it, the speakers simply aren't capable of playing any lower, so you get no benefit setting it lower than your receiver recommends. The whole purpose of Audyssey, YPAO or whatever system your receiver uses to calibrate, is get the sound in your room as close as it can to a reference sound, in other words how it is supposed to sound when the sound engineers produced the soundtrack.

This can be quite a different sound to what you're used to if you've always set up your systems by ear, but if you want it sound how it should, then you should leave it like this. Of course as it's your system, if you decide you prefer the bass a bit higher for example, then you're free to do that. This is what is called reference vs preference. The reference sound may not be exactly to your taste straightaway, but you're best to watch a couple of movies before making up your mind so you can get used to it before making a decision to tweak anything.

The one thing that you shouldn't do is mess about with the dials on the back of the subwoofer once you've ran calibration. If you are going to do it, then adjust through the receiver. If you move the speakers or subwoofer, or move the furniture around, then it's a good idea to calibrate again. Other than that, you're done. Go and listen to some music or watch some movies and enjoy your surround system, happy in the knowledge it's now all set up and performing properly! Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.

Sign in or sign up and post using a HubPages Network account. Comments are not for promoting your articles or other sites. Shoud i use steel wire mesh for protection from rat. One educated man in the field of electronics told me that for a 5. I have two stereo amps, do I need 4 more? And how do I wire everything to have sound playing from one source? Hello there, I have all speakers necisary but am not sure how to wire zed speakers.

For the back and front speakers do i wire the negative wire to the negative on a 3. Hi, I bought Sony Home theater 5. Sounds like you've broken the speakers by playing them too loudly. Sorry to hear that. The only solution is to buy a more powerful system that can handle the volume you want. I have a problem with my onkyo HT s, before i calibrate my speakers just to testing the sounds, the speakers set is clear and deep the bass subwoofer is so heat pumping in other words what i bought is perfect for what i want, then later on, after reading the manual, i prefer to calibrate my surround speaker according to the manual setup to make the sound more powerful and in effect, afterwards, done calibrating and start to test some heart pumping song from rock music, i was so disappointed because the sub woofer speakers are not responding clearly, i try to adjust adding some more subwoofer volume and it sounds like the speaker is going to break even in very low volume, i said "whats going on" i try to inspect some wiring and some given set up from receiver, everything is in garbage now, just like I'm listening to the mono speaker, i try also some default setting from receiver and its the same, please help me to solve my problem.

I am using microlab x15, is a 5. All speakers are connected but when i play sound from my laptop which the soundblaster is connected to only give me sound from front 3 and the Subwoofer and not the other 2 back speakers. Basically I've set up as instructed to connect 5. I have a 5. It comes with bluetooth and wifi. So I need to know can I increase it to 7. This could be one particular of the most useful blogs We've ever arrive across on this subject.

I'm also a specialist in this topic so I can understand your hard work. I can only receive sound out of my centre spkr surround right spkr and the sub woofer is very tinny sounding it frustrating me as I was told its the easiest system in the world to set up as it colour co ordinated a nine year old kid could do it so please help help help yours not as clever as a nine year old stevie doc many thanks in advance. Hi there I have a 5. Hi I have a Sony receiver connected to 5 speakers. But when I do the test for the sound , it gives me error Will this still put out same sound even though they are same..?

My surround speakers are connected to my computer but it increases it's sound extremely suddenly. You need to check the settings on your cable box. Usually you can tell it whether you want to have the sound output to the tv through hdmi or to a separate output. Just go into the menu and adjust it there.

I have a Kenwood 5. Hey great advice all the time you really know your stuff ,,so i was wondering if you could tell me what to do with a 7. Thanks for the great setup ideas. I have always been a little iffy on how to set up my speakers. Hey so I just got a pioneer 5. Hello, what are you playing through it?

It might be a case of setting up whatever you have going through it to 5. If you've done that then you should go through the output modes on the system itself. It may have defaulted to stereo plus sub, rather than 5. Hi, you need to set up the cable channel up so it uses the hdmi for picture and optical for audio. It is possible to do this as I've done it before but I can't recall the exact procedure from memory. The first thing I'd do in your shoes is download the full manual from the denon website, the answer is in there although the manual is pretty comprehensive.

After you've got the manual, do a search through google for ' batpigs denon to English dictionary'. Once you've read that you'll be able to understand the manual as it explains it well. So I plugged optical cable in and now Hi Ulric, well sky will only play 5. It's a quirk of their boxes, you'll need a separate optical lead if you want to get 5.

Your speaker wires do have to be connected positive to positive, negative to negative on both the receiver and the speaker side. If not, they will work, but not properly, so make sure that they are connected up correctly.

How to Hook up Surround Sound (with Pictures) - wikiHow

As far as pro logic goes, there is an option in the denon menu to set up the rear speakers. If you want to use all 7 speakers, then you can go through the 'surround parameter' menu and set the rears to use dolby pro logic IIx, this will turn a stereo or 5. It is a very good effect in my opinion. You may need to go through the PS3 menu to set the sound output up correctly, as if you feed the denon a 5. Double-check the Yamaha user's manual to see if you're not missing a setting or something.

How to Set up & Calibrate 5.1/6.1/7.1 Surround Sound Speaker System

Try a different HDMI cable. Thu Jul 27, 6: I have been volunteering at least half a year on this forum helping people to resolve the issue with ARC connection from Roku TV to Yamaha receivers. All I hear from Roku is crickets. That is an idea. That would be just wonderful. Maybe, it requires some communication with Yamaha. So, here I go again. You just do not here a sound. So, a simple fix, which still permits surround sound, is to slightly downgrade the protocol. Please let me know if it works for you.

Tue Dec 31, 5: I had to switch the receiver input to something else and back to AV4 to reestablish audio. I do not have sound on power-on either. Again, fiddling with the receiver inputs helps. What is you receiver and TV model? I would appreciate if Roku developers on this forum at least acknowledge the problem.

How to Connect a Stereo System

We should be able to check it online. Sun Jul 08, 7: I needed to use the audio input trick switch to AV3 and then back to AV4 using the Yamaha remote to complete the ARC handshake and that was a giant pain for my other family members. Works fine with mine. Sat Aug 11, 3: None of the written directions helped. There is an unheralded setting on the TV that is accessed like this: Once they are activated, everything works as it should through the receiver.